Single Jerry Can Holder - by Front Runner

$ 94.95
excl tax, excl works
Product Code
Lock your can, lock your cap, in this rattle and shake free mounting system. Perfectly suited for the Front Runner Slimline II Roof Rack but can be bolted to just about anything.

  • Proven gear and advice
    You can trust
  • Built off-road
  • Designed

The Front Runner Single Jerry Can Holder is designed to be mounted perpendicular ACROSS 2 slats. If you'd like to mount a single jerry can holder PARALLEL to the slats, you will need to use these brackets.

Since many of today's new jerry cans vary ever so slightly is size (due to manufacturing discrepancies), most fuel can mounting systems fail to secure the cans properly.

There is often wiggle room between the carrier and the can. And that gap, however slight, causes rattle and wear. What's the point in strapping down your cans if they aren't truly secure?

The Front Runner jerry can holders offer a smart no rattle no wear solution. The adjustable locking steel clasp means your cans can be secured firmly in place over a lifetime of off-road abuse.

For use with 20l / 5.3 gallon NATO/Wedco style military cans. Will not work with Scepter style cans.

The new bolt on top strap means provides greater convenience when removing the jerry can.

In addition, the steel strap downs cover the jerry can cap. Add your own padlock and you'll never have to worry about stolen fuel while on the road.

The Front Runner single jerry can holder is made of black powder coated stainless steel and is designed to easily bolt to the Front Runner Roof Racks using the flat slotted slats in the rack.

If a parallel, between slats placement is preferred this can be done with the use of Inter-Slat Brackets.

Consists of:
1x Jerry can holder base (non-welded)
1x Jerry can strap
1x Cross strap
1x Latch
Bolt kit

Materials used:
Black powder-coated 3CR12 stainless steel

Product Dimensions:
Overall Dimensions:
480mm (18.9") L x 160mm (6.3") W x 345mm (13.6") H

Base Dimensions:
480mm (18.9") L x 160mm (6.3") W x 50mm (2") H

Latch Buckle Dimensions:
45mm (1.8") W x 185mm (7.3") H

Strap Dimensions:
45mm (1.8") W x 3mm (0.1") Thick

Cross Strap Dimensions:
180mm (7.1") L x 45mm (1.8") W

2.82kg (6.2lbs)

For use with 20l / 5.3 gallon NATO/Wedco style military cans. Will not work with Scepter style cans.

*A PDF viewer is required to view the fitting instructions.

Product Questions
I would like to mount this on the front of the tray in front of a RTT. There would only be a few inches between the tent and the back of the holder. Can the strap be removed to access the can with something more noted directly behind the holder?
Question by: Richard Sumner
It's possible depending on how much space you actually have. You'll need 5.5 inches (14 cm) on either the back or the front of the holder for all actions to clear properly.
Answer by: Front Runner
Will this product work with plastic Jerry cans?
Question by: Haydn
Yes, it will work with the 20L plastic jerry can (WTAN002).
Answer by: Front Runner
will this holder work right for the 20l water jug also?
Question by: jeff
Yes, the Water Jerry Can (WTAN002) will fit in the Single Jerry Can Holder.
Answer by: Front Runner
My vehicle has an ARB roof rack with a mesh floor. How does the jerry can mount to my roof rack? What type of mounting hardware is included with the mount? Thank you.
Question by: Richard Spencer
All Front Runner Jerry Can Holders are designed to mount to our racks or any flat surface. It comes with short button head bolts for our racks, so to adapt to your mesh floor, you may need to make a trip to the hardware store for another fastening solution. Our tray has some pre drilled holes that are m8 sized. If you have any other question please feel free to give us a call.
Answer by: Front Runner
Choose Your Country/Region

middle east