10"/250mm LED Flood Light w/ Bracket - by Front Runner
2400 LUMEN LED flood light for illumination around vehicle and campsite. Comes standard with Front Runner air dam/rock guard mounting bracket for fitting to the front, side or rear of the Front Runner Slimline II Roof Rack.
- Proven gear and adviceYou can trust
- Built off-roadTough
- DesignedSmart
2400 LUMEN LED flood light for illumination around vehicle and campsite.
Comes standard with a Front Runner air dam/rock guard bracket for fitting to the front, side or rear of the Front Runner Slimline II Roof Rack.
No permanent wiring required. Just run power cord (Hella Extension Cord - 3m/10" - not included) from vehicle 12v accessory outlet to one of the 2 receptacles in bracket. The additional receptacle can be used to simultaneously power the light and other 12v accessories.
- Die cast aluminum housing is waterproof, dustproof and rattle proof. Built for Off-Road performance in harsh outdoor conditions.
- Expected LED life of 30,000 hours.
- Comes standard with powder coated stainless steel Slimline II air dam and rock guard Roof Rack mounting brackets. (Optional original Slimline roof rack brackets are available (RRAC053).
- 120 degree wide flood beam pattern for close but wide range illumination immediately surrounding the vehicle.
Consists of:
1 x LED Light and Bracket
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated 3CR12 Stainless Steel
Black powder coated Aluminum
Rubber
Product Dimensions:
330mm (13") L x 97.5mm (3.8") W x 98mm (3.9") H
Weight:
1.9kg (4.2lbs)
Special Notes:
ECOM076 is required to provide power to the light.
The LED light bracket has 2 Hella connection points.
One Hella connection point is used to provide power to the light and the other can be used for other accessories requiring 12V power.
The 2nd accessory point only has power when the light has power.
LED Light Specifications:
10" /240mm Single Row LED Lightbar
Input Voltage: 9-32 Volts DC
Power Consumption: 30 Watts
Amp Draw: 2.4 Amps @ 12 Volts
6 High Intensity CREE LEDs
Lumen Output: Approx. 2400
Beam Pattern: Flood
Beam Angle: 120 Degree Flood
Housing Material: Aluminum
Lens Material: Polycarbonate
Mounting Bracket: Black powder coated Stainless Steel
Dust Proof, Waterproof
1 x LED Light and Bracket
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated 3CR12 Stainless Steel
Black powder coated Aluminum
Rubber
Product Dimensions:
330mm (13") L x 97.5mm (3.8") W x 98mm (3.9") H
Weight:
1.9kg (4.2lbs)
Special Notes:
ECOM076 is required to provide power to the light.
The LED light bracket has 2 Hella connection points.
One Hella connection point is used to provide power to the light and the other can be used for other accessories requiring 12V power.
The 2nd accessory point only has power when the light has power.
LED Light Specifications:
10" /240mm Single Row LED Lightbar
Input Voltage: 9-32 Volts DC
Power Consumption: 30 Watts
Amp Draw: 2.4 Amps @ 12 Volts
6 High Intensity CREE LEDs
Lumen Output: Approx. 2400
Beam Pattern: Flood
Beam Angle: 120 Degree Flood
Housing Material: Aluminum
Lens Material: Polycarbonate
Mounting Bracket: Black powder coated Stainless Steel
Dust Proof, Waterproof
*A PDF viewer is required to view the fitting instructions.
Write Your Own Review
Product Questions
Can the 10" lights be tilted or angled at all during installation?
Question by: Eric
Definitely! The 10" light can be angled about 30 degrees downward from the horizontal position.
Answer by: Front Runner
How is this light activated / turned on?
Question by: Clint
It turns on once plugged in. They are made to plug into the vehicle's lighter outlet. If you choose to hardwire it then you can select a switch of your liking (purchased separately) to include during the installation process.
Answer by: Front Runner
I have your rack and just read the info on the front light and its ability to be mounted on the bottom and the flip up cover... I love this idea. Not sure I need a cover for side lights but is there any way to mount this on the bottom of the rack? I live in WA state with lots of trees and limbs hanging around and I just think it sticking out is asking for trouble.
Question by: David
This particular light can only clamp onto the side. The mounting system for this light bar won't allow for anythign else. Thank you!
Answer by: Front Runner
I have a Slimline II rack on my 4runner, mounted upside down to accommodate a roof top tent. I'm interested in the 10"/250MM LED FLOOD LIGHT W/ BRACKET. Will it mount successfully on the side of the Slimline II rack if I mount the light bracket from the underside of the rack rim.
Question by: Ray
Yes. you will be able to mount the 10"/250mm LED Flood Light w/ Bracket to your rack that is mounted upside down. Just note that with the rack upside down the light will hang a bit lower then normal.
Answer by: Front Runner
Can this light be hard wired to the vehicle instead of using the Hella plugs?
I'd rather it be controlled from accessory panel in the cab.
Question by: jason glasser
Yes, of course it can be hard wired. Little modification and some electrical knowledge will be needed.
Answer by: Front Runner
Will this 10" Flood Light item RRAC058 mount on the back of the Front Runner Slimline II Full Rack for my 2012 Jeep JK if I have the Stainless Steel Camp table item TBRA003 mounted under the rack as well?
Question by: Brian38501
You would have to do some measuring. If you have room to mount on the left or right sides of the table it would be best. Otherwise it would interfere when accessing your table.
Answer by: Front Runner
Product Questions
Can the 10" lights be tilted or angled at all during installation?
Question by: Eric
Definitely! The 10" light can be angled about 30 degrees downward from the horizontal position.
Answer by: Front Runner
How is this light activated / turned on?
Question by: Clint
It turns on once plugged in. They are made to plug into the vehicle's lighter outlet. If you choose to hardwire it then you can select a switch of your liking (purchased separately) to include during the installation process.
Answer by: Front Runner
I have your rack and just read the info on the front light and its ability to be mounted on the bottom and the flip up cover... I love this idea. Not sure I need a cover for side lights but is there any way to mount this on the bottom of the rack? I live in WA state with lots of trees and limbs hanging around and I just think it sticking out is asking for trouble.
Question by: David
This particular light can only clamp onto the side. The mounting system for this light bar won't allow for anythign else. Thank you!
Answer by: Front Runner
I have a Slimline II rack on my 4runner, mounted upside down to accommodate a roof top tent. I'm interested in the 10"/250MM LED FLOOD LIGHT W/ BRACKET. Will it mount successfully on the side of the Slimline II rack if I mount the light bracket from the underside of the rack rim.
Question by: Ray
Yes. you will be able to mount the 10"/250mm LED Flood Light w/ Bracket to your rack that is mounted upside down. Just note that with the rack upside down the light will hang a bit lower then normal.
Answer by: Front Runner
Can this light be hard wired to the vehicle instead of using the Hella plugs?
I'd rather it be controlled from accessory panel in the cab.
Question by: jason glasser
Yes, of course it can be hard wired. Little modification and some electrical knowledge will be needed.
Answer by: Front Runner
Will this 10" Flood Light item RRAC058 mount on the back of the Front Runner Slimline II Full Rack for my 2012 Jeep JK if I have the Stainless Steel Camp table item TBRA003 mounted under the rack as well?
Question by: Brian38501
You would have to do some measuring. If you have room to mount on the left or right sides of the table it would be best. Otherwise it would interfere when accessing your table.
Answer by: Front Runner