Hi-Lift Jack Bracket - by Front Runner

$ 165.00
incl. GST, excl. Shipping
Product Code
This 2 piece locking bracket easily bolts to the side of your Slimline II Roof Rack Tray for a rattle-free, off-road tough jack carrying solution. Fits all size Hi-Lift jacks.

  • Proven gear and advice
    You can trust
  • Built off-road
  • Designed
  • Made of heavy gauge 3CR12 stainless steel.
  • Finished with the same durable, weather resistant black powder coating as the Front Runner Slimline II Roof Rack.
  • Lockable. Uses small wire locks such as the Master Lock Luggage Lock model 4688D.
  • Consists of two (2) brackets - one to hold down the jack handle and the other to secure the base.
  • Mounts easily to the side rails of the Front Runner Slimline II Roof Rack.
  • Fits all size Hi-Lift Jacks.
Consists of:
1x Handle bracket
1x Base bracket
Bolt kit
Materials used:
Black powder-coated 3CR12 stainless steel
2.1kg (4.63lbs)

*A PDF viewer is required to view the fitting instructions.

Product Questions
Can I mount this Hi-Lift Jack Bracket with expedition rails?
Question by: Pete
Yes. Our hi-lift mount will work with our expedition rails installed.
Answer by: Front Runner
can this fit a Gen 1 slimline rack
Question by: Martin Pieper
Yes, it sure will! We provide the hardware for it to fit. Some simple drilling is required.
Answer by: Front Runner
I live in an area rife with petty property crime, and I'm trying to figure out the best way to lock my jack into this rack - do you have suggestions on specific padlocks or some other method of actually locking the lift into the bracket?
Question by: Charles Fisher
You can use a Cable Lock or a Long Shackle padlock to lock the base of the jack to the end plate of the Hi-Lift Jack Bracket (JADA010).
Answer by: Front Runner
Will this jack mount fit on the end of the slimline II rack?
Question by: John Bryant
The recommended fitment of the Hi-Lift Jack Mount (JADA010) on either the side profiles of the Roof Rack. We do not recommend mounting a Hi-Lift Jack on the front or the back of our rack.
Answer by: Front Runner
Hi, does a high-lift + mount fit on the rear end of the slimline on a discovery 3 so that the tail-gate still opens? Thanks! Sascha
Question by: Sascha
Hi - We don't recommend mounting a hi-lift Jack off the back of our rack. The supported mounting positions are on the sides of the racks! Hope this helps.
Answer by: Front Runner
I have the older Wind Cheetah, and want to mount the High-Lift Jack. Any suggestions? Thanks Andre
Question by: Andre Pretorius
Our Wind Cheetah racks were available in a higher 80mm profile and the 50mm lower profile. If your rack has the 50mm profile, our current high lift jack bracket will work, by drilling holes in side profile to mount it. All hardware is included in the kit. If your rack is the 80mm profile you can use the Bolt and clamp bracket (JADA005)
Answer by: Front Runner
Hi I want to ask, does the Hi-Lift jack bracket supports half rack? or does it has to be full rack?, thank you.
Question by: George Dai
Hey George, Our Hi-Lift Jack mounting brackets will work with half rack applications. You just have to make sure the rack is long enough to fit the size jack you have.
Answer by: Front Runner
Will the jack mount fit on one side of the slimline II rack when you have an awning attached on the other side and the tent installed?
Question by: Sean
The short answer is, YES. Depending on how you would like to mount your Jack, it may help to have the taller tent mount.
Answer by: Front Runner
Will this fit a landrover oem expedition rack? How does it attach to rack?
Question by: Dan
Most likely no, this bracket uses a specially designed c-clamp that fits flawlessly around the Slimline side rails.
Answer by: Front Runner
Choose Your Country/Region

middle east