40"/1016mm LED Flood/Spot Combo w/Off-Road Performance Shield - by Front Runner

$ 1,220.00
incl. GST, excl. Shipping
Product Code

This 40 inch LED Light Bar with spot and flood multi beam technology comes complete with a built in adjustable light shield, a Lightbar Isolator Kit and brackets to mount either below or in front of a Slimline II Roof Rack.

Out of stock
  • Proven gear and advice
    You can trust
  • Built off-road
  • Designed
  • 40 Inch Dual Row LED Light Bar features approximately 19,200 lumens.
  • Combination of 8 degree narrow spot beam pattern for focusing on long range distances AND 120 degree wide flood beam pattern for close but wide range illumination immediately surrounding the vehicle.
  • The aluminum housing is waterproof, dustproof and rattle proof. Built for Off-Road performance in harsh outdoor conditions.
  • Expected LED life of 30,000 hours.
  • Mounts to the front of a Front Runner Roof Rack via the T-slots of the front combined slat profile OR under the Rack using included mounting bracket solutions.
  • Mounting brackets are made of Aluminium and 3CR12 stainless steel and sealed with the same durable, weather resistant black powder coating as the Front Runner Roof Rack.
  • The robust light shield protects the 40 inch LED Light Bar from small rocks and can rotate 100 degrees not braking the beam pattern when the light is in use.
  • The light shield can additionally control light fall and prevent excessive glare on the vehicles hood/bonnet.
  • Optional Wiring Harness available (Single LED Wiring Harness with ATP Plug ).
  • Supplied with a Lightbar Isolator Kit, that fits into the heat-sink fins on the back of the 40"/1016mm LED Flood/Spot Combo, eliminating harmonic vibrations.
  • Includes all installation hardware and fitting instructions.

PLEASE NOTE: A minimum of 100mm (3.94 inches) clearance is needed between the bottom of the Front Runner Rack and the vehicle's roof in order to fit this product using the under rack brackets.

Consists of:
1 x 40" LED Light Bar (Multi Beam with Spot & Flood)
1 x Set of Front Rack Mount Brackets
1 x Set of Under Rack Mount Brackets
1 x Protective Front Cover
Installation Hardware
Fitting Instructions

Materials used:
Black powder coated Aluminium and 3CR12 stainless steel

Product Dimensions:
1110mm (43.7") L x 117mm (4.6") W x 78mm (3.1") H

6.7kg (14.7lbs)

Light Specifications:
40 Inch Dual Row
Input Voltage: 9-32 Volts DC
Power Consumption: 240 Watts / 16 Amp at 12 Volts
80 High Intensity CREE LEDs
Color Temp: 6000k
Lumen Output: Approx. 19,200lm
Beam Pattern: 8 Degree Spot Combination Flood
Protection: Over / Under Voltage protection
Reverse polarity protection
Housing Material: Aluminum extrusion
Mounting End Pieces: Die cast aluminum alloy
Lens Material: High Light Transmission Polycarbonate
Dustproof, Waterproof

*A PDF viewer is required to view the fitting instructions.

Product Questions
Do you sell just the brackets separately?
Question by: Randy De Brun
Yes. We recommend ordering our RRAC124 brackets.
Answer by: Front Runner
Does this come with the necessary wiring?
Question by: David
The light bar wire has a female Deutsch Tech connector on the end of it. It does not come with any other electrical component. The harness with a switch, relay, fuse, and male Deutsch Tech connector is sold separately and can be found with this SKU: ECOM077. It's a perfect match!
Answer by: Front Runner
when do you expect this to be back in stock?
Question by: Chris
The product is in route and should be back in stock in the next week or so. If you would like you may add the product to your wish list and as soon as it is back in stock you will be notified via email.
Answer by: Front Runner
Is it possible to still buy the previous version, that only fit underneath the rack?
Question by: Tom Skinner
This kit (RRAC101) comes with both the top and bottom mounts along with any needed hardware to install it on our rack.
Answer by: Front Runner
Dear I have a question about installing the 40" led bar on my slimline 2 roofrack of my defender. I would like to buy one but i dont know where i need to go with the cables, whats the best way to hide the cables? can someone help me with this? Btw the roofrack is superb! Kind regards jonas
Question by: Jonas
The loom can actually be fed through the snorkel, if one is fitted, to inside the engine compartment and through the firewall to the battery under the passenger seat. Spade lugs can be used as a clip by bending it over and locating it on the outside of windscreen rubber, cable tying the loom to the lug and running it to inside engine compartment if snorkel is not an option.
Answer by: Front Runner
Choose Your Country/Region

middle east